Beginner's Plumbing: What You Need for Bathtub Installation
Beginner's Plumbing: What You Need for Bathtub Installation
Blog Article
We have come across the article involving How to Install a Bathtub down the page on the web and reckoned it made good sense to talk about it with you on this site.
Mounting a bath tub isn't specifically rocket science, but it does require strong plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is likewise a reasonably difficult task. If the old bathtub is readily obtainable, the job can move speedily; if you have to open a wall surface to eliminate the old tub and place the new bath tub, the task is a lot harder. In either situation, the task is within a residence handyman's skills, although you will certainly need a helper to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified yourself for the job and are comfortable trying it. As opposed to employing a specialist to take over a halfway-completed project, it is far better to think about utilizing one prior to you begin. Opportunities are you may need a specialist plumber to make tube connections.
This article will certainly aid you set up a new tub in your bathroom if you have already bought a brand-new bathtub and also do not need to alter the arrangement of your previous water system pipelines.
Your devices as well as material checklist ought to consist of the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is separate the water supply. After doing so, activate the faucets to drain any type of water staying in the system. The process of removing the existing taps can be fairly bothersome due to the limited access that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly come from the pipes. When the supply pipelines have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning during this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making certain that the washing machines are in area between the tap and the sink. Secure the tap in place with the supplier provided backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet ports. The former type should be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the tub in the needed placement. The wood boards are helpful in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 little factors.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bath tub until the spirit level checks out degree.
To install taps, fit the bottom of the furthest flexible tap port to the proper supply pipeline by making a compression join; then do the same for the other tap.
Activate the water supply and examine all joints and also brand-new pipework for leaks and tighten them if necessary. Load the tub and additionally inspect the overflow outlet and also the typical outlet for leaks.
Finally, take care of the bathroom paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the tub ought to wait up until the tub has actually been used at the very least when as this will certainly resolve it right into its last position.
Preparing for the Installment
Firstly, the supporting framework supplied with the bath must be fitted (if required) according to the maker's directions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make sure that if the faucet features a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the taps system to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets making use of 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you make use of all of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently be ready to be suited its last placement.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to break a stiff seal, creating the water to pass through the wall in between the bath and also the tiling, bring about difficulties with wetness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes and cartridges, as well as can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Remember to always load the bathtub with water before securing, to enable the movement experienced when the tub remains in use. The sealer can fracture fairly early if you do not take into account this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily readily available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you liked our topic on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a ton for spending some time to read through our post. Sharing is good. One never knows, you may be helping someone out. Many thanks for going through it.
Got trouble? Ring! Report this page